一个平板有好多孔，程序目的为了检测是否有漏加工的孔
SNSLCT/SA(P1_0_0P0_0)
F(PLA_1)=FEAT/PLANE,CART,-630.2310,-932.1222,-943.3087,0.00148781,-0.00115741,0.99999822
MEAS/PLANE,F(PLA_1),4
PTMEAS/CART,-688.5620,-908.7690,-943.1901,0.00400397,0.00000000,0.99999198
PTMEAS/CART,-688.5820,-931.5615,-943.2256,0.03001612,0.00500269,0.99953690
PTMEAS/CART,-572.1880,-911.2810,-943.3724,-0.01301097,0.01201013,0.99984322
PTMEAS/CART,-571.6350,-976.9629,-943.4436,0.02801557,0.06403558,0.99755430
ENDMES
DECL/DOUBLE,PLA_1_I,PLA_1_J,PLA_1_K
PLA_1_I=OBTAIN/FA(PLA_1),6
PLA_1_J=OBTAIN/FA(PLA_1),7
PLA_1_K=OBTAIN/FA(PLA_1),8
F(CIR_1)=FEAT/CIRCLE,INNER,CART,-604.7864,-937.7296,-945.1245,PLA_1_I,PLA_1_J,PLA_1_K,30.0039
MEAS/CIRCLE,F(CIR_1),4
PTMEAS/CART,-619.7876,-938.2775,-945.1040,0.99996593,0.00800774,-0.00200193
PTMEAS/CART,-605.7654,-922.7594,-945.1170,0.02998651,-0.99955030,0.00000000
PTMEAS/CART,-589.8060,-936.9540,-945.1175,-0.99995950,-0.00899964,0.00000000
PTMEAS/CART,-619.7575,-936.9585,-945.1180,0.99992786,-0.01201115,0.00000000
ENDMES
CONST/CIRCLE,F(CIR_1),PROJCT,FA(CIR_1),FA(PLA_1)
DECL/DOUBLE,PLA_1_I,PLA_1_J,PLA_1_K
PLA_1_I=OBTAIN/FA(PLA_1),6
PLA_1_J=OBTAIN/FA(PLA_1),7
PLA_1_K=OBTAIN/FA(PLA_1),8
F(CIR_2)=FEAT/CIRCLE,INNER,CART,-605.3495,-969.6852,-945.3369,PLA_1_I,PLA_1_J,PLA_1_K,11.9500
MEAS/CIRCLE,F(CIR_2),4
PTMEAS/CART,-605.6990,-975.6584,-945.3410,-0.03701164,0.99931433,-0.00100031
PTMEAS/CART,-610.5306,-972.3121,-945.3405,0.99903147,-0.04400139,0.00000000
PTMEAS/CART,-605.5950,-963.7070,-945.3350,0.01099933,-0.99993901,0.00099994
PTMEAS/CART,-599.4786,-968.7050,-945.3330,-0.99985553,-0.01699754,0.00000000
ENDMES
CONST/CIRCLE,F(CIR_2),PROJCT,FA(CIR_2),FA(PLA_1)
DECL/DOUBLE,PLA_1_I,PLA_1_J,PLA_1_K
PLA_1_I=OBTAIN/FA(PLA_1),6
PLA_1_J=OBTAIN/FA(PLA_1),7
PLA_1_K=OBTAIN/FA(PLA_1),8
F(LIN_1)=FEAT/LINE,BND,CART,-604.7864,-937.7296,-945.1245,-605.3495,-969.6852,-945.3369,PLA_1_I,PLA_1_J,PLA_1_K
CONST/LINE,F(LIN_1),BF,FA(CIR_1),FA(CIR_2)
D(DAT_1) = DATSET/FA(PLA_1),ZDIR,ZORIG,FA(LIN_1),XDIR,YORIG,FA(CIR_1),XORIG,YORIG,ZORIG
RECALL/D(DAT_1)
MODE/PROG,MAN
SNSET/CLRSRF,FA(PLA_1),20.0000
GOTO/30.9185,2.7978,36.1900
DECL/CHAR,64,FILENAME,CIRNAME,FILE1,PTNAME
DECL/INTGR,I,PtNum
$$获取圆心坐标和直径
DECL/REAL,PX,PY,Pd
$$未加工的圆数
PtNum=ASSIGN/0
FILENAME=PROMPT/'ENTER THE NAME OF THE DATA FILE WITHOUT EXTENSION(请输入一个数据文件名!)'
FILE1=ASSIGN/CONCAT('E:\',FILENAME,'.TXT')
DID(F1)=DEVICE/STOR,FILE1
OPEN/DID(F1),DIRECT,INPUT
DO/ I,1,5,1
READ/DID(F1),PX,PY,Pd
BADTST/ON
SNSET/SEARCH,6.0000
PTNAME=ASSIGN/CONCAT('POI_',STR(I))
F(@PTNAME)=FEAT/POINT,CART,PX,PY,0,0,0,1
MEAS/POINT,F(@PTNAME),1
PTMEAS/CART,PX,PY,0
ENDMES
$$ check to see if the point feature was successfully measured.
$$ if not sucecess mesure the hole
IF/(BADPT())
SNSET/RETRCT,1.0000
SNSET/APPRCH,1.0000
DECL/DOUBLE,PLA_1_I,PLA_1_J,PLA_1_K
PLA_1_I=OBTAIN/FA(PLA_1),6
PLA_1_J=OBTAIN/FA(PLA_1),7
PLA_1_K=OBTAIN/FA(PLA_1),8
CIRNAME=ASSIGN/CONCAT('cir1_',STR(I))
F(@CIRNAME)=FEAT/CIRCLE,INNER,CART,PX,PY,-2,PLA_1_I,PLA_1_j,PLA_1_k,pd
MEAS/CIRCLE,F(@CIRNAME),4
ENDMES
CONST/CIRCLE,F(@CIRNAME),PROJCT,FA(@CIRNAME),FA(PLA_1)
ELSE
PtNum=ASSIGN/PtNum+1
ENDIF
BADTST/OFF
ENDDO
CLOSE/DID(F1)
ENDFIL
鲁公网安备37020002000329号