也是拿来玩的一个程序，是阵列圆，3行10列，但是个人总感觉不太理想，有谁有好的阵列程序，来出来晒晒，在此多谢了 话不说多了，上程序和图： MODE/DCC ASSIGN/V1 = 1 ASSIGN/XX = 0 ASSIGN/YY = 0 DO/ CIR1 =FEAT/CONTACT/CIRCLE,CARTESIAN,IN,LEAST_SQR THEO/<XX,YY,0>,<0,0,1>,5,0,360 ACTL/<90,20,0>,<0,0,1>,5,0,360 TARG/<XX,YY,0>,<0,0,1> ANGLE VEC=<1,0,0> DIRECTION=CCW SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO IF/V1<10 ASSIGN/XX = XX+10 ASSIGN/YY = YY END_IF/ IF/V1==10 ASSIGN/YY = 10 ASSIGN/XX = XX END_IF/ IF/V1>10 AND V1<20 ASSIGN/YY = 10 ASSIGN/XX = XX-10 END_IF/ IF/V1==20 ASSIGN/YY = 20 ASSIGN/XX = XX END_IF/ IF/V1>20 AND V1<30 ASSIGN/YY = 20 ASSIGN/XX = XX+10 END_IF/ ASSIGN/V1 = V1+1 UNTIL/V1>30 [attachimg]1366[/attachimg]

补充一个在当前圆柱孔-10的地方增加一个高度点，上程序： MODE/DCC ASSIGN/V1 = 1 ASSIGN/XX = 0 ASSIGN/YY = 0 ASSIGN/V2 = "cir" DO/ CIR1 =FEAT/CONTACT/CIRCLE,CARTESIAN,IN,LEAST_SQR THEO/<XX,YY,0>,<0,0,1>,5,0,360 ACTL/<90,20,0>,<0,0,1>,5,0,360 TARG/<XX,YY,0>,<0,0,1> ANGLE VEC=<1,0,0> DIRECTION=CCW SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO PNT1 =FEAT/CONTACT/VECTOR POINT,CARTESIAN THEO/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> ACTL/<90,20,0>,<0,0,1> TARG/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO IF/V1<10 ASSIGN/XX = XX+10 ASSIGN/YY = YY END_IF/ IF/V1==10 ASSIGN/YY = 10 ASSIGN/XX = XX END_IF/ IF/V1>10 AND V1<20 ASSIGN/YY = 10 ASSIGN/XX = XX-10 END_IF/ IF/V1==20 ASSIGN/YY = 20 ASSIGN/XX = XX END_IF/ IF/V1>20 AND V1<30 ASSIGN/YY = 20 ASSIGN/XX = XX+10 END_IF/ ASSIGN/V1 = V1+1 UNTIL/V1>30 [attachimg]1367[/attachimg]

厉害，一个循环就搞定3列10行！

[quote] 原帖由 [b]wskmnm[/b] 于 2010-12-30 20:49:00 发表 厉害，一个循环就搞定3列10行！ [/quote]我知道没你厉害啦，有什么问题请指教，或者把你的好东东拿出来分享一下下嘛，不要那么小器呀

再次优化一下，请勿见笑！！！友友们有更好的东东晒出来一下呀 MODE/DCC ASSIGN/V1 = 1 ASSIGN/XX = 0 ASSIGN/YY = 0 DO/ CIR1 =FEAT/CONTACT/CIRCLE,CARTESIAN,IN,LEAST_SQR THEO/<XX,YY,0>,<0,0,1>,5,0,360 ACTL/<90,20,0>,<0,0,1>,5,0,360 TARG/<XX,YY,0>,<0,0,1> ANGLE VEC=<1,0,0> DIRECTION=CCW SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO PNT1 =FEAT/CONTACT/VECTOR POINT,CARTESIAN THEO/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> ACTL/<90,20,-10>,<0,0,1> TARG/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO IF/V1==10 OR V1==20 ASSIGN/XX = XX ASSIGN/YY = YY+10 END_IF/ IF/V1<10 ASSIGN/XX = XX+10 END_IF/ IF/V1>10 AND V1<20 ASSIGN/XX = XX-10 END_IF/ IF/V1>20 AND V1<30 ASSIGN/XX = XX+10 END_IF/ ASSIGN/V1 = V1+1 UNTIL/V1>30 :D :D :D :D :D :D

再次优化 MODE/DCC ASSIGN/V1 = 1 ASSIGN/XX = 0 ASSIGN/YY = 0 DO/ CIR1 =FEAT/CONTACT/CIRCLE,CARTESIAN,IN,LEAST_SQR THEO/<XX,YY,0>,<0,0,1>,5,0,360 ACTL/<90,40,0>,<0,0,1>,5,0,360 TARG/<XX,YY,0>,<0,0,1> ANGLE VEC=<1,0,0> DIRECTION=CCW SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO PNT1 =FEAT/CONTACT/VECTOR POINT,CARTESIAN THEO/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> ACTL/<90,40,-10>,<0,0,1> TARG/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO IF/V1==10 OR V1==20 OR V1==30 OR V1==40 OR V1==50 ASSIGN/XX = XX ASSIGN/YY = YY+10 END_IF/ IF/V1<10 ASSIGN/XX = XX+10 END_IF/ IF/(V1>10 AND V1<20) OR (V1>30 AND V1<40) ASSIGN/XX = XX-10 END_IF/ IF/(V1>20 AND V1<30) OR (V1>40 AND V1<50) ASSIGN/XX = XX+10 END_IF/ ASSIGN/V1 = V1+1 UNTIL/V1>50 :D :D :D :D :D :D

更加优化了，但还是求更好的方法，友友们加油啊！ MODE/DCC ASSIGN/V1 = 1 ASSIGN/XX = 0 ASSIGN/YY = 0 DO/ CIR1 =FEAT/CONTACT/CIRCLE,CARTESIAN,IN,LEAST_SQR THEO/<XX,YY,0>,<0,0,1>,5,0,360 ACTL/<90,40,0>,<0,0,1>,5,0,360 TARG/<XX,YY,0>,<0,0,1> ANGLE VEC=<1,0,0> DIRECTION=CCW SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO PNT1 =FEAT/CONTACT/VECTOR POINT,CARTESIAN THEO/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> ACTL/<90,40,-10>,<0,0,1> TARG/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO IF/V1==10 OR V1==20 OR V1==30 OR V1==40 OR V1==50 ASSIGN/XX = 0 ASSIGN/YY = YY+10 END_IF/ IF/V1<>10 AND V1<>20 AND V1<>30 AND V1<>40 AND V1<>50 ASSIGN/XX = XX+10 END_IF/ ASSIGN/V1 = V1+1 UNTIL/V1>60 :D :D :D :D :D

更加更加优化了，下面的程序中，要测多少圆和点，只需在“UNTIL/V1>60”中把60改成所要测的数即可，不说了，上程序： MODE/DCC ASSIGN/V1 = 1 ASSIGN/XX = 0 ASSIGN/YY = 0 DO/ CIR1 =FEAT/CONTACT/CIRCLE,CARTESIAN,IN,LEAST_SQR THEO/<XX,YY,0>,<0,0,1>,5,0,360 ACTL/<0,60,0>,<0,0,1>,5,0,360 TARG/<XX,YY,0>,<0,0,1> ANGLE VEC=<1,0,0> DIRECTION=CCW SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO PNT1 =FEAT/CONTACT/VECTOR POINT,CARTESIAN THEO/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> ACTL/<0,60,-10>,<0,0,1> TARG/<CIR1[V1].X,CIR1[V1].Y,-10>,<0,0,1> SHOW ADVANCED MEASUREMENT OPTIONS=NO SHOW_CONTACT_PARAMETERS=NO ASSIGN/V2 = V1%10 IF/V2==0 ASSIGN/XX = 0 ASSIGN/YY = YY+10 END_IF/ IF/V2<>0 ASSIGN/XX = XX+10 END_IF/ ASSIGN/V1 = V1+1 UNTIL/V1>61 :D :D :D :D :D

为什么要加一个高度？用安全平面不可以吗？

[quote] 原帖由 [b]CMM11[/b] 于 2011-1-9 23:45:00 发表 为什么要加一个高度？用安全平面不可以吗？ [/quote]对不起，我没有用高度，也没有用安全平面！！！