大家好！我用的是PC-DMIS CAD软件，工作中遇到了这样问题，下面是我的检测程序： 启动 =建坐标系/开始,回调:, LIST= 是 建坐标系/终止 模式/手动 探测/ 2,1 移动速度/ 30 飞行/开,3 加载测头/D55050 测尖/T1A90B0, 柱测尖 IJK=0, 1, 0, 角度=180 格式/文本,选项,标题,符号, ;标称值,测定值,公差,偏差,超差,偏差角度, 平面1 =特征/平面，直角 理论值/153.8313,364.1845,-383.2129,-0.0160048,0.9996798,0.0196016 实际值/153.8313,364.1845,-383.2129,-0.0160048,0.9996798,0.0196016 测定/平面,3 触测/基本,284.5825,366.7918,-409.4255,-0.0160048,0.9996798,0.0196016,284.5825,366.7918,-409.4255,使用理论值 = 是 触测/基本,103.461,362.811,-354.2965,-0.0160048,0.9996798,0.0196016,103.461,362.811,-354.2965,使用理论值 = 是 触测/基本,73.4503,362.9506,-385.9168,-0.0160048,0.9996798,0.0196016,73.4503,362.9506,-385.9168,使用理论值 = 是 终止测量/ 工作平面/Y 正 圆1 =特征/圆，直角,内,最小二乘方 理论值/86.3449,354.7132,-362.2374,0,1,0,22.6412 实际值/86.3449,354.7132,-362.2374,0,1,0,22.6412 测定/圆,4,工作平面 触测/基本,75.1078,354.7847,-360.8707,0.9926849,0,-0.1207337,75.1078,354.7847,-360.8707,使用理论值 = 是 移动/圆弧 触测/基本,97.5696,354.7393,-360.7742,-0.9916098,0,-0.1292673,97.5696,354.7393,-360.7742,使用理论值 = 是 移动/圆弧 触测/基本,87.4378,354.6929,-350.9688,-0.0965382,0,-0.9953293,87.4378,354.6929,-350.9688,使用理论值 = 是 移动/圆弧 触测/基本,87.4343,354.6358,-373.5062,-0.0962333,0,0.9953588,87.4343,354.6358,-373.5062,使用理论值 = 是 终止测量/ 测尖/T1A0B0, 柱测尖 IJK=0, 0, 1, 角度=0 圆2 =特征/圆，直角,外,最小二乘方 理论值/173.0169,418.3171,-414.8102,0,1,0,65.1405 实际值/173.0169,418.3171,-414.8102,0,1,0,65.1405 测定/圆,3,工作平面 触测/基本,205.1605,422.3173,-409.5561,0.9869025,0,0.161318,205.1605,422.3173,-409.5561,使用理论值 = 是 移动/圆弧 触测/基本,173.2873,416.6905,-382.2411,0.0083047,0,0.9999655,173.2873,416.6905,-382.2411,使用理论值 = 是 移动/圆弧 触测/基本,141.0526,415.9437,-408.5564,-0.9813929,0,0.1920105,141.0526,415.9437,-408.5564,使用理论值 = 是 终止测量/ 点1 =特征/点，直角 理论值/173.8681,365.1453,-415.8528,-0.0160048,0.9996798,0.0196016 实际值/173.8681,365.1453,-415.8528,-0.0160048,0.9996798,0.0196016 构造/点,射影,圆2,平面1 点2 =特征/点，直角 理论值/86.2172,362.6876,-362.0811,-0.0160048,0.9996798,0.0196016 实际值/86.2172,362.6876,-362.0811,-0.0160048,0.9996798,0.0196016 构造/点,射影,圆1,平面1 A2 =建坐标系/开始,回调:启动, LIST= 是 建坐标系/找平,Y 正,平面1 建坐标系/旋转圆,Z 正,至,点1,AND,点2,关于,Y 正 建坐标系/旋转偏置,57.6996,关于,Y 正 建坐标系/平移,X 轴,点1 建坐标系/平移,Y 轴,点1 建坐标系/平移,Z 轴,点1 建坐标系/终止 模式/DCC 移动/点,43.5938,293.4175,266.5877 测尖/T1A90B0, 柱测尖 IJK=0.0157, 0.9997, -0.0198, 角度=-179.2424 移动/点,173.7557,110.8326,386.7582 平面2 =特征/平面，直角 理论值/-3.0073,-0.0045,26.8672,0.0000047,1,-0.0001697 实际值/-3.0237,-0.0022,26.8758,-0.0000114,1,-0.0001218 测定/平面,6 触测/基本,111.7027,-0.0165,-27.1736,0.0000047,1,-0.0001697,111.684,-0.0117,-27.1652,使用理论值 = 是 触测/基本,102.5765,0.002,22.9956,0.0000047,1,-0.0001697,102.5591,0.0075,23.0042,使用理论值 = 是 触测/基本,42.3015,-0.0065,66.8577,0.0000047,1,-0.0001697,42.2811,-0.004,66.8635,使用理论值 = 是 移动/点,43.6771,31.1023,137.2048 移动/点,-74.6347,33.7355,138.7544 触测/基本,-67.9797,0.0076,65.5861,0.0000047,1,-0.0001697,-67.9883,0.0042,65.5959,使用理论值 = 是 触测/基本,-103.2426,-0.0034,22.5792,0.0000047,1,-0.0001697,-103.263,-0.004,22.5885,使用理论值 = 是 触测/基本,-103.4021,-0.01,10.3583,0.0000047,1,-0.0001697,-103.4151,-0.0054,10.368,使用理论值 = 是 终止测量/ 移动/点,-87.0044,49.716,9.115 移动/点,-86.3754,50.6242,55.524 圆3 =自动/圆, 显示所有参数=是, 显示触测=是 理论值/-87,0,55,0,1,0,22.6 实际值/-86.922,0,54.9746,0,1,0,22.6295 目标值/-87,0,55,0,1,0 理论厚度 = 0, 直角, 内, 圆弧, 最小二乘方, 出错 = 否 ,$ 自动移动 = 是, 距离 = 20, 相对测量 = 无, 读位置 = 否, 查找孔 = 无, 重新测量 = 否 ,$ 测点数 = 5, 起始 = 0, 永久 = 0, 间隙 = 3, 间距 = 0 ,$ 起始角 = 0, 终止角 = 360, 深度 = 10 ,$ 角矢量 = -1,0,0 测定/圆 触测/基本,-98.3,-10,55,1,0,0,-98.2312,-10.0048,55.0094 触测/基本,-90.4919,-10,65.7469,0.309017,0,-0.9510565,-90.474,-10.0007,65.7239 触测/基本,-77.8581,-10,61.642,-0.809017,0,-0.5877853,-77.8054,-10.0015,61.6685 触测/基本,-77.8581,-10,48.358,-0.809017,0,0.5877853,-77.7835,-10.0013,48.301 触测/基本,-90.4919,-10,44.2531,0.309017,0,0.9510565,-90.5039,-10.001,44.2391 终止测量/ 移动/点,-81.1588,60.7945,437.7014 测尖/T1A0B0, 柱测尖 IJK=0.0135, 0.0196, 0.9997, 角度=-0.9172 移动/点,-104.8571,72.0914,203.3708 圆4 =自动/圆, 显示所有参数=是, 显示触测=是 理论值/0,21,0,0,1,0,65.22,220 实际值/0.0127,21,-0.0038,0,1,0,65.2383,220 目标值/0,21,0,0,1,0 理论厚度 = 0, 直角, 外, 圆弧, 最小二乘方, 出错 = 否 ,$ 自动移动 = 否, 距离 = 20, 相对测量 = 无, 读位置 = 否, 查找孔 = 无, 重新测量 = 否 ,$ 测点数 = 5, 起始 = 0, 永久 = 0, 间隙 = 3, 间距 = 0 ,$ 起始角 = 180, 终止角 = 360, 深度 = 0 ,$ 角矢量 = 1,0,0 测定/圆 触测/基本,-32.5901,21,1.1381,-0.9993908,0,0.0348995,-32.5878,20.9942,1.1461 触测/基本,-22.6528,21,23.4577,-0.6946584,0,0.7193398,-22.6424,21.0021,23.4609 触测/基本,0,21,32.61,0,0,1,0.0071,21.0017,32.6157 触测/基本,22.6528,21,23.4577,0.6946584,0,0.7193398,22.6734,20.9969,23.4618 触测/基本,32.5901,21,1.1381,0.9993908,0,0.0348995,32.6104,21.0059,1.1398 终止测量/ 移动/点,108.4074,273.2311,301.426 点3 =特征/点，直角 理论值/-0.0001,-0.009,0.0036,0.0000047,1,-0.0001697 实际值/0.013,-0.0055,-0.0013,-0.0000114,1,-0.0001218 构造/点,射影,圆4,平面2 点4 =特征/点，直角 理论值/-87,0.0007,55,0.0000047,1,-0.0001697 实际值/-86.922,0.0002,54.9746,-0.0000114,1,-0.0001218 构造/点,射影,圆3,平面2 A1 =建坐标系/开始,回调:A2, LIST= 是 建坐标系/找平,Y 正,平面2 建坐标系/旋转圆,Z 正,至,点3,AND,点4,关于,Y 正 建坐标系/旋转偏置,57.6996,关于,Y 正 建坐标系/平移,X 轴,点3 建坐标系/平移,Y 轴,点3 建坐标系/平移,Z 轴,点3 建坐标系/终止 A3 =建坐标系/开始,回调:A1, LIST= 是 建坐标系/平移偏置,Y 轴,-60 建坐标系/终止 测尖/T1A90B-97.5, 柱测尖 IJK=0.9892, -0.1463, -0.0106, 角度=-91.1256 工作平面/Z 正 A4 =建坐标系/开始,回调:A3, LIST= 是 建坐标系/旋转偏置,-8,关于,Z 正 建坐标系/终止 移动/点,46.8958,299.6495,397.9615 移动/点,89.7992,15.5233,404.4128 工作平面/X 正 移动/点,171.1277,-19.7869,-15.1952 孔1 =自动/圆, 显示所有参数=是, 显示触测=是 理论值/143,-20,-31,1,0,0,10.8 实际值/143,-19.5334,-30.8511,1,0,0,11.0439 目标值/143,-20,-31,1,0,0 理论厚度 = 0, 直角, 内, 圆弧, 最小二乘方, 出错 = 否 ,$ 自动移动 = 是, 距离 = 20, 相对测量 = 无, 读位置 = 否, 查找孔 = 无, 重新测量 = 否 ,$ 测点数 = 5, 起始 = 0, 永久 = 0, 间隙 = 3, 间距 = 0 ,$ 起始角 = 0, 终止角 = 360, 深度 = 8 ,$ 角矢量 = 0,0,1 测定/圆 触测/基本,135,-20,-25.6,0,0,-1,134.9977,-20.0008,-25.3708 触测/基本,135,-25.1357,-29.3313,0,0.9510565,-0.309017,135.0008,-24.8688,-29.4195 触测/基本,135,-23.174,-35.3687,0,0.5877853,0.809017,135.0002,-23.0003,-35.1318 触测/基本,135,-16.826,-35.3687,0,-0.5877853,0.809017,134.9956,-16.6735,-35.5599 触测/基本,135,-14.8643,-29.3313,0,-0.9510565,-0.309017,134.9974,-14.2806,-29.1435 终止测量/ 孔2 =自动/圆, 显示所有参数=是, 显示触测=是 理论值/143,-20,31,1,0,0,10.8 实际值/143,-19.72,31.187,1,0,0,11.0031 目标值/143,-20,31,1,0,0 理论厚度 = 0, 直角, 内, 圆弧, 最小二乘方, 出错 = 否 ,$ 自动移动 = 是, 距离 = 20, 相对测量 = 无, 读位置 = 否, 查找孔 = 无, 重新测量 = 否 ,$ 测点数 = 5, 起始 = 0, 永久 = 0, 间隙 = 3, 间距 = 0 ,$ 起始角 = 0, 终止角 = 360, 深度 = 8 ,$ 角矢量 = 0,0,-1 测定/圆 触测/基本,135,-20,25.6,0,0,1,134.9826,-20.0065,25.6972 触测/基本,135,-14.8643,29.3313,0,-0.9510565,0.309017,134.9927,-14.5773,29.2446 触测/基本,135,-16.826,35.3687,0,-0.5877853,-0.809017,134.9954,-16.585,35.7033 触测/基本,135,-23.174,35.3687,0,0.5877853,-0.809017,135.003,-23.2193,35.4264 触测/基本,135,-25.1357,29.3313,0,0.9510565,0.309017,135.0048,-24.922,29.4106 终止测量/ 孔3 =自动/圆, 显示所有参数=是, 显示触测=是 理论值/143,20,31,1,0,0,10.8 实际值/143,20.3205,31.1977,1,0,0,10.9251 目标值/143,20,31,1,0,0 理论厚度 = 0, 直角, 内, 圆弧, 最小二乘方, 出错 = 否 ,$ 自动移动 = 是, 距离 = 20, 相对测量 = 无, 读位置 = 否, 查找孔 = 无, 重新测量 = 否 ,$ 测点数 = 5, 起始 = 0, 永久 = 0, 间隙 = 3, 间距 = 0 ,$ 起始角 = 0, 终止角 = 360, 深度 = 8 ,$ 角矢量 = 0,0,-1 测定/圆 触测/基本,135,20,25.6,0,0,1,134.9949,20.0049,25.7719 触测/基本,135,25.1357,29.3313,0,-0.9510565,0.309017,134.9949,25.424,29.2447 触测/基本,135,23.174,35.3687,0,-0.5877853,-0.809017,134.9949,23.4154,35.7019 触测/基本,135,16.826,35.3687,0,0.5877853,-0.809017,135.0027,16.8273,35.3617 触测/基本,135,14.8643,29.3313,0,0.9510565,0.309017,135.0029,15.1291,29.4234 终止测量/ 孔4 =自动/圆, 显示所有参数=是, 显示触测=是 理论值/143,20,-31,1,0,0,10.8 实际值/143,20.4759,-30.8089,1,0,0,11.1164 目标值/143,20,-31,1,0,0 理论厚度 = 0, 直角, 内, 圆弧, 最小二乘方, 出错 = 否 ,$ 自动移动 = 是, 距离 = 20, 相对测量 = 无, 读位置 = 否, 查找孔 = 无, 重新测量 = 否 ,$ 测点数 = 5, 起始 = 0, 永久 = 0, 间隙 = 3, 间距 = 0 ,$ 起始角 = 0, 终止角 = 360, 深度 = 8 ,$ 角矢量 = 0,0,-1 测定/圆 触测/基本,135,20,-36.4,0,0,1,134.9956,20.0009,-36.328 触测/基本,135,25.1357,-32.6687,0,-0.9510565,0.309017,134.9942,25.6539,-32.8279 触测/基本,135,23.174,-26.6313,0,-0.5877853,-0.809017,134.9966,23.5119,-26.1708 触测/基本,135,16.826,-26.6313,0,0.5877853,-0.809017,135.0027,16.8235,-26.6298 触测/基本,135,14.8643,-32.6687,0,0.9510565,0.309017,135.0038,15.2053,-32.5552 终止测量/ 移动/点,166.3345,19.3248,-34.2207 平面3 =特征/平面，直角 理论值/143.9483,3.3708,-2.3709,0.9999889,0.0045496,-0.0011891 实际值/143.9366,3.3649,-2.3659,0.999989,0.0045783,-0.0009965 测定/平面,4 触测/基本,143.8744,6.8161,-33.7394,0.9999889,0.0045496,-0.0011891,143.8692,6.8069,-33.7319,使用理论值 = 是 触测/基本,143.8793,25.1383,0.2651,0.9999889,0.0045496,-0.0011891,143.8657,25.139,0.2698,使用理论值 = 是 触测/基本,144.0816,-19.0992,1.1984,0.9999889,0.0045496,-0.0011891,144.0692,-19.1134,1.2032,使用理论值 = 是 触测/基本,143.958,0.6279,22.7925,0.9999889,0.0045496,-0.0011891,143.9424,0.627,22.7955,使用理论值 = 是 终止测量/ 移动/点,164.5772,2.8914,22.5477 移动/点,166.5409,28.625,408.5912 移动/点,-105.9362,432.8902,485.3383 尺寸 位置1= 圆 的位置孔1 单位=毫米 ,$ 图示=开 文本=关 乘数=100.00 输出=两者 轴 标称值 测定 正公差 负公差 偏差 超差 Y -20.0000 -19.5334 0.2000 -0.2000 0.4666 0.2666 --------> Z -31.0000 -30.8511 0.2000 -0.2000 0.1489 0.0000 -------#- 终止尺寸 位置1 尺寸 位置2= 圆 的位置孔2 单位=毫米 ,$ 图示=开 文本=关 乘数=100.00 输出=两者 轴 标称值 测定 正公差 负公差 偏差 超差 Y -20.0000 -19.7200 0.2000 -0.2000 0.2800 0.0800 --------> Z 31.0000 31.1870 0.2000 -0.2000 0.1870 0.0000 --------# 终止尺寸 位置2 尺寸 位置3= 圆 的位置孔3 单位=毫米 ,$ 图示=开 文本=关 乘数=100.00 输出=两者 轴 标称值 测定 正公差 负公差 偏差 超差 Y 20.0000 20.3205 0.2000 -0.2000 0.3205 0.1205 --------> Z 31.0000 31.1977 0.2000 -0.2000 0.1977 0.0000 --------# 终止尺寸 位置3 尺寸 位置4= 圆 的位置孔4 单位=毫米 ,$ 图示=开 文本=关 乘数=100.00 输出=两者 轴 标称值 测定 正公差 负公差 偏差 超差 Y 20.0000 20.4759 0.2000 -0.2000 0.4759 0.2759 --------> Z -31.0000 -30.8089 0.2000 -0.2000 0.1911 0.0000 --------# 终止尺寸 位置4 尺寸 距离1= 2D 距离圆 孔1 至 圆 孔2 平行 至 Z 轴, 无半径 单位=毫米 ,$ 图示=关 文本=关 乘数=10.00 输出=两者 轴 标称值 测定 正公差 负公差 偏差 超差 M 62.0000 62.0381 0.2000 -0.2000 0.0381 0.0000 -----#--- 尺寸 距离2= 2D 距离圆 孔3 至 圆 孔4 平行 至 Z 轴, 无半径 单位=毫米 ,$ 图示=关 文本=关 乘数=10.00 输出=两者 轴 标称值 测定 正公差 负公差 偏差 超差 M 62.0000 62.0066 0.2000 -0.2000 0.0066 0.0000 ----#---- 尺寸 距离3= 2D 距离圆 孔1 至 圆 孔4 平行 至 Y 轴, 无半径 单位=毫米 ,$ 图示=关 文本=关 乘数=10.00 输出=两者 轴 标称值 测定 正公差 负公差 偏差 超差 M 40.0000 40.0093 0.2000 -0.2000 0.0093 0.0000 ----#---- 尺寸 距离4= 2D 距离圆 孔2 至 圆 孔3 平行 至 Y 轴, 无半径 单位=毫米 ,$ 图示=关 文本=关 乘数=10.00 输出=两者 轴 标称值 测定 正公差 负公差 偏差 超差 M 40.0000 40.0404 0.2000 -0.2000 0.0404 0.0000 -----#--- 因图纸要求加工面上的孔的角度是8°，而我的测尖校的是7.5°,不知对检测数据能差多少？如果是10°、13°，哪又怎么办？是不是校一个比较接近的角度？